Guset User Download PDF. Publications: 93; Followers: 0. GReddy Profec B spec 2 Manual. Created Date: 8/14/ PM. Category: All. 0. Embed. Improper tuning of the Profec B-spec II may cause damage to the engine. GReddy 3 Way Fitting Double Sided Tape Air Filter Instruction Manual. Please make. pdf · Greddy Profec B 3 Knob Boost Controller Installation Instruction Manual, M. pdf · Greddy Profec B Spec Ii 2 Boost Controller Installation Instruction.
|Published (Last):||15 August 2006|
|PDF File Size:||13.37 Mb|
|ePub File Size:||10.70 Mb|
|Price:||Free* [*Free Regsitration Required]|
Overboosting may cause damage to the engine.
Parts List Pressure sensor Valve unit harness Pressure harness 2. The Display unit is packaged with the SD card already inserted. Tools profex for installation: This feature can be used with the Optional Remote Switching System sold separately. This is available at any computer supply retailer. Installation Diagram Diagram 1: Vehicle with factory boost controlling solenoid valve Dual Port Actuator Disconnect the connector and the vacuum lines off from the solenoid valve and plug up the all the vacuum ports.
Installation Diagram Diagram manuak Vehicle with factory boost controlling solenoid valve Single port actuator Disconnect the connector and the manuwl lines off from the solenoid valve and plug up the all the vacuum ports. Then, secure the Valve assembly to the body using the supplied M6 Bolt and Rubber washer. Also used to setup the optional signal harness and Warning gauges when installed with this unit.
The boost controller feature will still operate without performing this setup, but without confirming the rpm, throttle position and grefdy speed signal, the RPM OFFSET feature will not operate. This feature will automatically program the e for best boost response and consistant boost curve.
What’s missing? Tell us about it.
See next page for the learning procedure. Select this mode and input the desired boost proffec. P will indicate phase 1 in the upper right corner of the display.
The kept high boost mode that can be turned on for a set amount of time or on constantly. This is where the adjustment starts. See Initial Setting on page Set the Limiter to turn down the boost when the pressure exceeds the warning point. The Peak Hold type can be selected. PEAK – – – – – Display the highest boost monitored. See page 27 for throttle input signal setup. NAME Input mwnual to label each input signal channel.
Input up to 8 letters. UNIT Select the unit for the input signal.
GReddy PRofec B Quick : Install Manual
Select a blank space if proper unit is not one of the options. Use the optional External Input Signal Harness sold separately and select one to use as output signal.
The rpm signal can be inputted by using the optional External Input Signal Harness sold separately or through the e-manage unit. UNIT Select the unit for the selected meter type. Turn the engine off and re-update the unit. There are 4 different display format to choose from, Digital, Graph, Gauge, and Bar graph.
Record 3 hours of input signals including the e-manage signals can be recorded while in the Display mode. Play Back Play back the recorded data in the display mode. If you pause the play back and change the Display mode to e-manage Map display screen, the recorded e-manage data can be played back.
This Harness is used when controlling the ignition timing. D e-manage Operation 1. Inputting Values Move the cursor to the target cell using the 4-way navigation button, and press SET knob to select the cell. D lrofec Operation 4. Selecting multiple cells To input a value to a block of cells, hi light the cells by holding down the SHIFT button while moving the cursor with the 4-way navigation button. Map Trace Profex feature will hi-light the cell that is currently reading.
Map Select Place check marks on the features you grrddy to program. V RPM Setup on the main unit. This will allow the values below the inputted value gredxy opening to be recognized as accelerator OFF fully closed. Export Used to export all the data to the Main Unit. When the e and e-manage is linked, they are communicating at real time. When a setting is changed, it will send it to e-manage automatically. Also See for e Instruction manual – 55 pages.
Page of 55 Go. Add to my manuals Add. Related Manuals for GReddy e No related manuals. Page 2 Overboosting may cause damage to the engine. Product Features Take Boost feature.
Page 8 Installation Diagram Diagram 1: Page 9 Installation Diagram Diagram 2: Page 32 4 Reconnect the 12 pin Ignition harness back to the e-manage unit.
Manuak 41 This Harness is used when controlling the ignition timing. Page 42 D e-manage Operation 1. Page 43 D e-manage Operation 4. Page 48 D-4 ADD. Page 53 Main Unit. Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only current page. Manuql print the manual completely, please, download it. Don’t show me this message again. Got it, continue to print. Don’t have an account?