ASTM D Pull Off Test Standard – Free download as PDF File .pdf), Text File .txt) or read online for free. ASTM D and BS EN ISO describe several different test apparatus; The tensile pull-off method for adhesion testing, as outlined in ASTM D and . ASTM A/AM Steel, Sheet and Strip, Heavy-Thickness Coils, Hot- Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy.

Author: Taushura Fenrikasa
Country: Serbia
Language: English (Spanish)
Genre: Career
Published (Last): 18 September 2014
Pages: 105
PDF File Size: 3.37 Mb
ePub File Size: 18.89 Mb
ISBN: 225-3-60404-625-9
Downloads: 89045
Price: Free* [*Free Regsitration Required]
Uploader: Nejora

Method A, which appeared in previous versions of this standard, has been eliminated as its f use is for testing on concrete substrates see Test Method D It is the responsibility of the user of this standard to e1 appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use. Depending on the radius of the surface, the results could have greater variability with lower values and averages.

Active view current version of standard Translated Standard: Standards monitoring is d free service designed for you who wish to be alerted of changes to or new editions of the standards required in your work. Active view current version of standard. Therefore, when a series of results will be compared with one another or used for statistical analysis, asttm type of apparatus, substrate, test procedures, glue type, and if scoring is used should be the same for the r considered.

Pull-off strength of coatings from concrete is described in Test Method D Link to Active This link will always route to the current Active version of the standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The moment new editions of the standards you monitor are released, changes are made, or appendixes are published, you will be alerted by email. It is imperative to identify the test method used when reporting results.

  CUENTO LOS FUGITIVOS DE ALEJO CARPENTIER PDF

The procedure in this standard was developed for use on flat surfaces.

ASTM D – 09E1 PDF

09w1 Combining values from the two systems may result in non-conformance with the standard. Measurements are limited by the strength of adhesive bonds between the loading fixture and the specimen surface or the cohesive strengths of the glue, coating layers, and substrate. Fracture will occur along the weakest plane within the system comprised of the test fixture, glue, coating system, and substrate, and will be exposed by the fracture surface.

This test method serves as a means for uniformly preparing and testing coated surfaces, and evaluating and reporting the results.

Note 2—Method A, which 90e1 in previous versions of this standard, has been eliminated as its main use is 09e11 testing on concrete substrates see Test Method D Webprint Printed and bound. The benefits of a subscription: Failure will occur along the weakest plane within the system comprised of the test fixture, adhesive, coating system, and substrate, and will be exposed by the fracture surface. This includes change in glue, load fixture size, substrate coating cure time, pull rate, environmental conditions, if the coating is scored, or using a different device.

They are capable of applying a concentric load and counter load to a single surface so that coatings can be tested even though only one side is accessible.

This test method maximizes tensile stress as compared to the shear stress applied by other methods, such as scratch or knife adhesion, and results may not be comparable. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

This service is not 09f1 if you are a URL user where you do not log in with an email address. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.

  CA3130 DATASHEET PDF

Aetm d441 method is applicable to x portable apparatus meeting the requirements for determining the pull-off strength of a coating v4541 this standard see Annexes.

ASTM D4541 – 09E1 PDF

A web subscription provides an easy and secure access to standards, and you are guaranteed to always have the latest edition. Pull-off strength of coatings from concrete is described in Test Method D The procedure d this standard was developed for metal substrates, but may be appropriate for other rigid substrates such as plastic and wood. Monitoring Standards monitoring is a free service designed for you who wish to be alerted of changes to or new editions of the standards required in your work.

Results should only be assessed for each test method and not be compared with other instruments.

You need to log in before adding standards to the monitoring service. Historical Version s — view previous versions of standard. There are five instrument types, identified as Test Methods B-F. Results obtained by each test method may give different results. Note 1—The procedure in this standard was developed for metal substrates, but may be appropriate for other rigid substrates such as plastic and wood. Link to Active This link will always route to the current Active version of the standard.

This ensures that you are always up-to-date and saves you both time and money. Subscription — always available and updated A web subscription provides asstm easy and secure access to standards, and you are guaranteed to always have the latest edition.