most recent revision of the AAMA and. field testing protocols. AAMA 08,. “Voluntary Specification for Field Testing of. Newly Installed Fenestration. The AAMA (Voluntary Specification for Field Testing of Newly Installed Fenestration Products) is a field-testing guide developed by the American. AAMA Voluntary Specification for field testing of newly installed fenestration products. Includes Air Infiltration and Water Penetration.

Author: Kigahn Tojakinos
Country: Bosnia & Herzegovina
Language: English (Spanish)
Genre: Photos
Published (Last): 8 December 2017
Pages: 305
PDF File Size: 18.79 Mb
ePub File Size: 14.74 Mb
ISBN: 582-9-18920-847-6
Downloads: 96669
Price: Free* [*Free Regsitration Required]
Uploader: Taura

This guide illustrates test procedures to ensure aamaa and moisture penetration is minimized in new window installations. In addition, the AAMA guide provides verbiage that can be directly inserted into project specifications, saving time and effort.

The only problem with the verbiage provided is that it is often inserted in a generic aaja that does not provide details as to the areas, quantity, and specific testing pressures. It is up to the contractor to ensure these testing parameters are established.

Once testing parameters are specified, the testing agency ensures that proper procedures were followed during the construction installation process.

Typically, a sampling of windows from the project is selected and tested. The construction contract will appoint a party responsible for the cost of the testing. The number of tests depends on the size and budget of the project.

The project architect, manager, or owner specifies the amount and locations of the windows to be tested; this happens either early in the project or 502-8 three intervals in the case of large projects: With a large project, testing early on can prevent expensive repairs if a design flaw is identified during the first phase of testing.

  EUROPEES ARRESTATIEBEVEL PDF

Normally, if a window fails, the contractor should be prepared for a wider scope of testing. One-week notice prior to water testing is usually 5002-08 to all construction crew members concerned with window installation. It is not recommended to notify anyone of the actual test locations until the testing agency arrives onsite.

Water penetration observed when testing windows will be given extra attention for the remainder of the project. Before testing, the window installation is visually observed.

AAMA | Field Testing Quality Control

Are the edges perfectly horizontal and vertical? Is the window square? What is the drainage design? How is the installation quality?

Have flashing and sealing been properly finished? Then both air 502-80 water leakage in that order are determined using a test chamber of constant pressure. A predetermined amount of air leakage is allowable; however, no water leakage is permitted at all.

A specified pressure is maintained while any escaping air is measured.

AAMA Water Spray Testing

Water leakage uses the same method while spraying the window from outside to observe indoor penetration. 502–08 moisture not coming in through the window, but getting in somehow, will be subject to further forensic investigation. Guidelines for the type of equipment to use and test procedures to follow are specified in the AAMA If the window installation was completed within 6 months, and there is not a building occupancy permit COthen the AAMA is the right document to use.

  JBPM DEVELOPER GUIDE PDF

BDG utilizes professional testing equipment that is calibrated to each specific testing standard for accurate results.

AAMA Water Spray Testing

Our field consultants are properly trained and knowledgeable of all testing standards. BDG has extensive knowledge of most building systems and specializes in forensic water intrusion aa,a.

This allows us to not only properly test fenestrations on new construction projects, but also pinpoint the cause of any test failures and provide accurate recommendations to achieve successful testing results.

Failures during quality assurance new construction testing can result in unnecessary delays that impact your bottom line. If you are looking for a reputable second or third-party testing company to perform accurate professional testing, provide concise reports, and help you through the entire process, contact BDG today.

We provide testing services throughout the United States from our headquarters located in Atlanta, GA. Professional services based on accurate information that helps you or your company make the right decision regarding your project or asset.

Give us a call to discuss your next project. Building Diagnostics Group, Inc.

MISSION Professional services based on accurate information that helps you or your company make the right decision regarding your project or asset.